Correct setup/programming of SKU 2001710003 10-100V Digital Battery Capacity te

[Martin Keogh April 29, 2019 at 2:16 am Post count: 0]

#35822 Reply |

I have a 24volt 12ah 6S6P lithium battery.

How is it best to set up/program the <span id=”productTitle” class=”a-size-large”>DROK 10-100V Digital Battery Capacity Tester (SKU 2001710003)?</span>

Thanks
<h1 class=”product-name” data-spm-anchor-id=”2114.10010108.1000016.i0.1ecc5c73jAPRkl”></h1>

[DrokKeymaster April 29, 2019 at 7:29 am Post count: 2971]

#35825 Reply |

Hello Martin Keogh,

Thanks for writing in.

For lithium battery, please refer to below instruction.  If there are any more questions, please kindy contact us.

Best regards.

[Christopher Pedersen May 28, 2020 at 5:03 am Post count: 0]

#38914 Reply |

How do you save settings. I have this connected to 48v golf cart, and I have to setup the settings in option 3 everytime I turn the screen off and back on. How do I get the settings I setup to save?

[DrokKeymaster May 28, 2020 at 9:53 am Post count: 2971]

#38923 Reply |

Hello Christopher Pedersen，

Do you mean you need to reprogram battery specification？

After programing and hold the on/off button, it should save setting unless  change setting in menu 1 .

Could you please tell us more details about your operation?

Best regards,

DROK

[Chuck Storlie June 5, 2020 at 6:52 pm Post count: 0]

#39251 Reply |

Please send programing instructions on the 10-100 volt meter. Panel meter.  It’s not very understandable.   Having trouble saving settings and exiting settings to normal on/off position.

[Steven June 20, 2020 at 10:08 pm Post count: 0]

#39833 Reply |

This reply has been marked as private.

[DrokKeymaster June 22, 2020 at 8:50 am Post count: 2971]

#39902 Reply |

Hello Steven，

Are you talking about 2001710003 meter？Could you please tell us more details about your problem？

Do  you mean you disconnect battery?

Best regards.

[Thomas Hirte June 23, 2020 at 3:10 am Post count: 0]

#39945 Reply |

I have my meter (model 2001710003) connected to a car battery (12V Lead-acid) that I use in my camper to run my CPAP.  What specific settings (e.g. L#, and limits e.g. 12.6V?) should be used to monitor this battery.   Currently it shows 100% capacity, but I have used it for 3 days without charging.

[DrokKeymaster June 23, 2020 at 7:32 am Post count: 2971]

#39956 Reply |

Hello Thomas Hirte,

For 12v lead-acid, please select P12V in menu “1–“.  You can refer to the program method in above post.

Any more questions, please contact us.

Best regards.

[Scott carpenter February 16, 2021 at 12:47 am Post count: 0]

#60713 Reply |

Confused on the programming of 2001710003 for 48v golf cart. Have #1 set to F48v. For the #2 on and off, #3 voltage parameters. and #4buzzer not sure what to set

[DrokKeymaster February 20, 2021 at 8:57 am Post count: 2971]

#61165 Reply |

Hello Scott carpenter,

If you program menu 1–, please ignore menu 3–. They both are battery specificatin setting. Meter only save the last setting. Menu 3– is custom setting, you have to set minmum and maximum battery voltage.

Assume you set alaram value as 12v and enable this feature, when battery voltage reaches 12v, buzzer will sound.

Best regards.

 

[Sean Elledge March 15, 2021 at 6:37 pm Post count: 0]

#63594 Reply |

I properly set-up a lead-acid battery (golf cart) for 48 volts (P-48V).  This is a brand new set of batteries with an overnight fresh charge and the DROK meter registers 48 volts with only 75%  battery life remaining.  Why isn’t it 100%?  Did I do something wrong?

[DrokKeymaster March 16, 2021 at 7:15 am Post count: 2971]

#63644 Reply |

Hello Sean Elledge,

Are you talking about this item, #2001710003? https://www.amazon.com/dp/B07759SLYP?ref=myi_title_dp

Is the voltage reading correct? And is there any device drawing power from battery?

Best regards.

[MIKE SWILLEY December 14, 2021 at 5:10 pm Post count: 0]

#85718 Reply |

How do I provide a 20v charge to calibrate?

[DrokKeymaster December 17, 2021 at 8:25 am Post count: 2971]

#85879 Reply |

Hello MIKE SWILLEY,

Please connect accurate 20v voltage directly to “B+,B-“and then enter calibration menu.

Best regards.

[Author]

Posts