VAC8010F-80V non-functioning KWH display

[michael ward September 6, 2020 at 1:09 pm Post count: 0]

#45593 Reply |

sorry

the answer to your question is yes that’s my unit

[DrokKeymaster September 7, 2020 at 7:49 am Post count: 2971]

#45673 Reply |

Hello michael ward，

Do you mean you modife wireless module?

Please kindly notice the voltage range for this meter can’t be over 80v.

Best regards.

 

[Remus Matesan November 14, 2020 at 7:59 am Post count: 0]

#52257 Reply |

Hello,

VAC8010F can connect to PC?

Best regards

[DrokKeymaster November 16, 2020 at 7:12 am Post count: 2971]

#52399 Reply |

Hello Remus Matesan，

This item can’t be connected to PC.

 

[Mohamed November 21, 2020 at 12:45 pm Post count: 0]

#52794 Reply |

This reply has been marked as private.

[DrokKeymaster November 23, 2020 at 7:25 am Post count: 2971]

#52801 Reply |

Hello Mohamed，

Are you taling about this item? https://www.droking.com/Digital-Meter-Multifunction-Panel-Meter-DC-6V-80V-300A-999-KW-LCD-Display-Tester-Monitor-Meter-Multimeter-Thermometer

Would you please tell us your setting parameters?

Best regards.

[Aroen May 8, 2021 at 2:52 pm Post count: 0]

#69789 Reply |

Hai,

Everything works well, exept it shows 30,3 volts where in reality it is 24,6 volts.

Cant find any volt callibration in the menu…..

do I overlook something?

greetz,

Aroen

 

 

 

[DrokKeymaster May 9, 2021 at 7:33 am Post count: 2971]

#69877 Reply |

Hello Aroen,

May I know which item it is?

[Aroen July 3, 2021 at 5:59 am Post count: 0]

#75558 Reply |

VAC8010F

sorry for late answer.
Hospital came by….

[DrokKeymaster July 4, 2021 at 7:07 am Post count: 2971]

#75651 Reply |

Hello Aroen,

If voltage reading is incorrect, you can try calibration. Please refer to below instruction.

Adjustable power supply is required.

1. Hook it up correctly with adjustable power supply. Please makesure load current is off in this case.
2. Power on. Supply voltage is set to 12v and current is 11A.
3. Before calibrating voltage, we can reset the current zero. Short press the down button to move cursor to CER, then short press the ok button (the middle button) to reset current zero.
4. Move cursor to NCP, then hold the ok button to enter calibration menu, then release button.
5. Short press ok button to switch the voltage range from 0-20v to 20-120v. And supply voltage is set as “54v”. Then adjust displayed voltage until it is the same as load voltage.
6. Short press ok button to switch back to 0-20v voltage range. And supply voltage is set as “12v”. Then adjust display voltage until it is the same as load voltage.
7. Just repeat above two calibration steps until displayed voltage and load voltage are the same when supply voltage is 12v and 54 v. Then calibration is finished.

[Xanderone February 3, 2022 at 6:25 am Post count: 0]

#88867 Reply |

@Michael ward. I recently purchased this item vac8010f and boy was I so disappointed with the range. Is it Bluetooth or WiFi, I wonder.

But now I wish to extend the range. What radio tranciever components do you suggest I use for both the transmitter end and the receiver end?

 

Thanks.

[TonySParticipant September 7, 2023 at 2:53 pm Post count: 2]

#117053 Reply |

How do I set the vac8010f for Charging or discharging mode?

Can I do a factory reset?

 

I would like to read Accumulated remaining AH and also Accumulated Energy?

 

At the moment the reading for both is “0” and I have tried everything I can think of so far?

• This reply was modified 1 year, 3 months ago by  TonyS.

[TonySParticipant September 7, 2023 at 3:05 pm Post count: 2]

#117056 Reply |

Sorry fr posting the same 2 times but I was trying to ask from a answer given earlier.

My question in context is:

“Hello Dale Kramer，

In charging mode, kwh value increases. In discharging mode, it dicreases. When it is 0, it will not change again.

Best regards.”

How do I set the vac8010f for Charging or discharging mode?

Can I do a factory reset?

I would like to read Accumulated remaining AH and also Accumulated Energy?

At the moment the reading for both is “0” and I have tried everything I can think of so far?

[Author]

Posts