You are here:>>Wiring for DROK DC 0-120V 0-100A Digital Multimeter
Wiring for DROK DC 0-120V 0-100A Digital Multimeter 2017-05-30T03:57:47+00:00

Home › Forums › Panel Meter Support › Wiring for DROK DC 0-120V 0-100A Digital Multimeter

Viewing 15 posts - 1 through 15 (of 35 total)
1 2 3 Next
  • Author
    Posts
  • Michael
    May 30, 2017 at 3:57 am
    Post count: 0
    #17956 Reply |

    Need wiring diagram for for this unit:

    https://www.amazon.com/DROK-Multimeter-Charge-Discharge-Electricity-Overvoltage/dp/B01M5CWR2P/ref=cm_cr_arp_d_product_top?ie=UTF8

    Drok
    Keymaster
    May 31, 2017 at 8:56 am
    Post count: 2971
    #18002 Reply |

    Hello Michael,
    Thank you for writing in.
    About wiring instruction, please refer to this instruction.
    200193
    More questions, please don’t hesitate to contact us.
    Best regards.

    Michael Diogo
    June 19, 2017 at 12:25 am
    Post count: 0
    #18693 Reply |

    No where to be seen are figures 2-4, 2-5, 2-6. Also you claim that the meter will capture data up to 100 Amps. There is no way a #10 wire will not burn under a 100 amp DC load! The buss bar cannot accept any larger wire, not sure a #10 will even fit. Please supply schematics and instructions that make sense.

    Drok
    Keymaster
    June 19, 2017 at 9:45 am
    Post count: 2971
    #18716 Reply |

    Hello Michael Diogo,
    Sorry for the mistake in instruction.
    We will update the instruction as soon as possible. Please ignore the figures 2-4, 2-5. There are only two wirig diagarm Figure 1 and Figure

    rwizard
    July 25, 2017 at 6:10 pm
    Post count: 0
    #19838 Reply |

    I am considering purchase of this module. Michael was kind enough to send me a link to this page, but I need more info. Two questions:

    (1) Is there a user manual I can download?

    (2) Can I use the relay to turn power on and off with an external switch or a software command?

    Thanks.

    Drok
    Keymaster
    July 26, 2017 at 9:45 am
    Post count: 2971
    #19844 Reply |

    Hello rwizard,
    Thank you for writing in.
    As the picture showed,you can download the manual from Amazon product page.
    sample
    It’s not suitable to use the relay to turn power on and off here.
    Any more questions, please feel free to contact us.
    Best regards.

    Sam
    September 6, 2017 at 2:29 pm
    Post count: 0
    #21485 Reply |

    <p style=”text-align: left; padding-left: 30px;”> Hello, I am using this to measure the charge levels for a battery bank in a solar system and purchased this so that it could measure the net charge and discharge. Please clarify use of the VIN-, Vext+ and Vext-</p>
     

    thank you

    Drok
    Keymaster
    September 7, 2017 at 3:38 am
    Post count: 2971
    #21493 Reply |

    Hello Sam,
    Thanks for writing in.
    We can’t open this product link.

    Would you please send it again? Or you can just tell us the ASIN number .
    With your help, we can find solution as soon as possible.
    Best regards,
    DROK

    William Scully
    September 13, 2017 at 2:26 pm
    Post count: 0
    #21781 Reply |

    I have installed per Figure 1 Two-wire wiring diagram.  What is acceptable ‘small current’ to VIN- and what is the benefit using VIN- (you show it as optional)?

    Drok
    Keymaster
    September 15, 2017 at 9:40 am
    Post count: 2971
    #21862 Reply |

    Hello William Scully,
    Thanks for writing in.
    Would you please tell us if you are talking the following item?
    200193
    When the measuring current is below 2A, you can use VIN- terminal. That will be more precise.
    Best regards.

    William Scully
    September 15, 2017 at 12:14 pm
    Post count: 0
    #21866 Reply |

    Yes, it is 200193.  Is VIN- connected to the same Negative post cable connecting Power to shunt (in my case this is the end of the 4 x 12 volt battery bank)?

    Sam
    September 15, 2017 at 11:10 pm
    Post count: 0
    #21876 Reply |

    SKU 200193

    Sam
    September 15, 2017 at 11:14 pm
    Post count: 0
    #21877 Reply |

    SKU 200193

    What is the purpose of Vext+ and Vext-?

    Drok
    Keymaster
    September 18, 2017 at 9:47 am
    Post count: 2971
    #21900 Reply |

    Hello,William Scully
    When you use “VIN-” terminal, the wiring is almost the same to the figure 1,which is connect to “VIN+”. The only difference is to change the “VIN+” into “VIN-“.
    Best regards.

    Drok
    Keymaster
    September 18, 2017 at 9:54 am
    Post count: 2971
    #21901 Reply |

    Hello Sam,
    When you measure 0-10V voltage, “Vext+” and “Vext-” terminals need to be connect external power supply. The power supply should be DC10-30v.
    Best regards.

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 35 total)
1 2 3 Next
Reply To: Wiring for DROK DC 0-120V 0-100A Digital Multimeter
Your information: