You are here:>>Drok
Drok

Forum Replies Created

Viewing 15 posts - 2,896 through 2,910 (of 2,965 total)
  • Author
    Posts
  • Drok
    Keymaster
    Post count: 2971

    Hi, thank you for your business. you bought the ” Pb12V lead-acid battery” Size Battery Capacity Tester, right? Please note that this is used for Pb12V lead-acid battery, so it cannot monitor your gel lithium 12v 200AH battery. If you want to test it, you should choose the ” 3 pcs lithium batteries 12V” size. Any queries should you have pls feel free to contact us!Thanks.

    Drok
    Keymaster
    Post count: 2971
    in reply to: DC Motor Controller #2148

    Hi Sam, did you check the wires (winding displacement) of the potentiometer? Pull out then plug it into again. If you still cannot adjust it, maybe some components were broken. If the current is too large, it will destroy some internal components.

    Any way, If it still work for you, could you please contact us from your Amazon order, we will find a solution for you.

    Thanks for your understanding.
    DROK

    Drok
    Keymaster
    Post count: 2971
    in reply to: DC Motor Controller #2138

    Dear Sam, did the power indicator lights on? Did the wires connected the potentiometer loose? Could you please tell us more details about your using environment? what’s the input and output and what’s the load and the wiring? please send us a picture to let us check what is the problem detail? Thanks!

    Drok
    Keymaster
    Post count: 2971

    Hi,
    The supplies ability of the module is 20A maxium, it is not rated but adaptive that depends on the requirements of your load. the voltage regulator can be able to tolerate the currents ranging from 50mA to 15A.
    Any other question, feel free to contact us.
    Best regards

    Drok
    Keymaster
    Post count: 2971
    in reply to: D85 Digital Meter #2087

    Dear Kishore, some of DC meters can connect the shunt in Positive side of the load, but some not. which meter do you want to connect? Thanks!

    Drok
    Keymaster
    Post count: 2971

    Dear Diana A, did you buy this 20V 2A NC Power Module? please note that this is Step down mode, input voltage must be higher than 3V. So if the input is DC 5.1V, then set it for U-OUT 5.0V, it cannot work.

    Do you mean that when you changed the input to 12v, but the output still had nothing change? Could you please tell us what’s the wring. If you can, we sincerely hope you can send us some photos.

    Thanks!
    DROK

    Drok
    Keymaster
    Post count: 2971

    Dear Johna142,
    Thanks for your message. we are striving to improve ourselves in terms of service, quality, sourcing, etc. Any questions, don’t hesitate to write back to us.
    Thanks!

    Drok
    Keymaster
    Post count: 2971

    Dear Mike Groszko,
    Sorry for the delay.
    Could you please tell us which one do you want to know? Could you please give us the product link, or maybe you can give us your order number.
    Thanks!

    Drok
    Keymaster
    Post count: 2971

    hello,
    please download the firmware from dropbox.
    please manipulate following this imageimageimageimage
    and then,click ” 确定 “.
    lastly, please find a USB cable and connection, the fireware will automatic upgrade.
    hope this will help you.

    best regards

    Drok
    Keymaster
    Post count: 2971

    hi,
    we are sorry for mistake, this module starts in OFF mode, it can’t change to ON state. hope you can understand.
    best regards

    Drok
    Keymaster
    Post count: 2971

    hi,
    could you please send the link of this product to us??
    we can’y sure which one do you asked.
    waiting for your reply.
    best regards

    Drok
    Keymaster
    Post count: 2971

    hi,
    please check these imagescurrent testvoltage test
    we are sorry it is I not I:O.
    U is for voltage; P is for power; I is for current; and C is for capacity.
    so the meter reading is 0.75A.
    hope this will help you.
    best regards

    Drok
    Keymaster
    Post count: 2971

    hi,
    yes, flash the firmware can change the BT name.
    we are sorry there are a little annoying voice when playing loudly.
    adjust the volume of the machine button can decrease the annoying voice.
    hope this will help you.
    best regards

    Drok
    Keymaster
    Post count: 2971

    hi,
    thanks for the images.
    is this product your asked?? Meter AC 80-500V
    if yes, please check the following information.
    if the voltage is 110V or 220V, the 2 wire is hot and a ground.
    if the voltage is 380V, the 2 wire are hots.
    hope this will help you.
    best regards

    Drok
    Keymaster
    Post count: 2971
    in reply to: Soft Start Step up #2038

    dear friend,
    we are deeply sorry for any inconvenience may have caused you.
    here is the datasheet datasheet
    and we are sorry we don’t have a DC Converter with a “soft start”feature.
    hope you can understand.
    best regards

Viewing 15 posts - 2,896 through 2,910 (of 2,965 total)